低压静电场辅助冷冻对竹笋品质的影响

为研究低压静电场辅助冷冻对竹笋冻结特性的影响，以冻结曲线、硬度、水分损失率、水分迁移、冰晶形态和组织微观结构为指标，探究低压静电场辅助冷冻（－35 ℃）和普通冷冻（－35 ℃）条件下竹笋品质的变化规律。结果表明：低压静电场辅助冷冻提高了冻结效率，改变了冰晶形态及分布，减轻了组织微观结构破损程度，改善了解冻汁液流失情况。与静电板间距10、20、30、40 cm处的冷冻竹笋解冻后水分损失率分别为14.16%、12.58%、9.73%、10.44%，显著低于对照组（21.01%）（P＜0.05），硬度分别为461.19、507.48、496.65 g和455.31 g，显著高于对照组（350.70 g）（P＜0.05）。低场核磁共振分析结果表明，在低压静电场辅助冷冻下竹笋解冻后汁液流失减少，扫描电子显微镜观察结果显示，竹笋纤维排列整齐，组织微观结构保持较好。低压静电场辅助冷冻可有效改善竹笋品质，可为利用低压静电场进行果蔬的冷冻贮藏和冷链运输提供参考。     

Microbial coupled photocatalytic fuel cell with a double Z-scheme g-C3N4/ZnO/Bi4O5Br2 cathode for the degradation of different organic pollutants

A novel heterostructure of g-C₃N₄/ZnO/Bi₄O₅Br₂ (ZB-3) was designed, and used in the microbial coupled photocatalytic fuel cell (MPFC). It can effectively improve electron utilization efficiency and pollutant degradation using this double Z-scheme heterojunction structure. The current–time (I–t) curves demonstrated that the current density of ZB-3 was higher than that of ZnO, ZnO/Bi₄O₅Br₂ (ZB-1), g-C₃N₄/ZnO (ZB-2). Electrochemical impedance spectroscopy (EIS) indicated ZB-3 possessed the minimum charge-transfer resistance. This MPFC for degrading rhodamine B (RhB) and tetracycline (TC) under different conditions were developed using these materials. Even in the dark condition, MPFC with g-C₃N₄/ZnO/Bi₄O₅Br₂ demonstrated 93% and 82% degradation efficiency for RhB and TC, respectively. Furthermore, the electron transport mechanism of the MPFC and ZB-3 were proposed. It paves the approach for more efficient pollutant degradation via MFC photocatalysis.     

Evaluation of cut cell cartesian method for simulation of a hook and claw type hydrogen pump

Hook and claw pumps are used for recirculation of excess hydrogen in fuel cells. Optimization of the pump design is essential. Computational Fluid Dynamic (CFD) is an effective method for performance optimization. However, it is difficult to conduct CFD simulation because of the sharp cusp of the rotor profile. Cut cell Cartesian mesh could be the solution to handle this complex and moving geometries. The aim of this paper is to evaluate ANSYS Forte for hook and claw pumps. Firstly, the conservation accuracy of the cut cell cartesian mesh is verified using an adiabatic piston cylinder case. Then, simulation results of hook and claw type pump are compared with experimental data. Finally, simulation results of air and hydrogen are compared. The results show that the CFD simulation of hook and claw pumps using cut cell cartesian mesh could provide an efficient and effective approach for the optimization of the system.     

Analysis and proposition of limiting current density measurement protocol

Limiting current density at different temperatures, backpressures, and balance gases can be used to separate molecular diffusion resistance, Knudsen diffusion resistance and local transport resistance of membrane electrode assembly (MEA). However, the measurement of limiting current density has no unified protocol. The diverse choices in the literature, either in the control of current or voltage or in the atmosphere like relative humidity and O₂ concentrations, make it difficult to compare the results and identify the true bottleneck hindering the mass transport. In this work, the current-voltage curves obtained by current scanning/stepping and voltage scanning/stepping methods under dilute O₂ of different concentrations and a wide range of relative humidity were measured and analyzed systematically. It is found that the voltage stepping method is superior to the other three ways of control for the reliable determination of the limiting current density. Aided with simultaneous electrochemical impedance spectroscopy measurement, the limiting current density can be determined with pinpoint accuracy. When the limiting current density is just used to qualitatively evaluate different MEA, the voltage scanning method can be used instead for its high time efficiency. The selection of the atmosphere also plays an important role in suppressing the distortion from excessive water and reducing the spurious contribution from proton conduction resistance. It is found that O₂ concentrations at 0.5 vol% and relative humidity at 90% can give the best estimation of O₂ transport resistance in membrane electrode assembly.     

Effect of micro-cracks on the in-plane electronic conductivity of proton exchange membrane fuel cell catalyst layers based on lattice Boltzmann method

Micro-cracks commonly occur on the catalyst layers (CLs) during the manufacturing of catalyst coated membranes (CCMs). However, the crack shape parameters effect on CLs in-plane (IP) electronic conductivity λ_s is not clear. In this work, the relationship between crack parameters and the λ_s is obtained based on the two-dimensional (2D) multiple-relaxation time (MRT) lattice Boltzmann method (LBM). The LBM numerical model is validated by the normalized λ_s experiment applied on three different home-made cracked CLs, and the parameter study focus on crack width, length, quantity and phase angle are carried out. The results show that the decrease of λ_s has different sensitivity |k| to the parameters above. The crack width has little effect on λ_s decrease, and the |k_w| is 0.038. However, crack arm length and quantity show more significant impact, which |k_l| and |k_N| are 0.753 and 0.725, respectively. The CLs with different crack propagation directions show significant anisotropy on λ_s, and a 53.53% decrease in λ_s is observed between 0° and 90° crack phase angle change. To manufacture a high electronic conductivity CL, crack initiation and migration mitigation are highly encouraged.     

High performance asymmetric supercapacitor based on 3D microsphere-like 1T-MoS2 with high 1T phase content

1T phase molybdenum disulfide (1T-MoS₂) has aroused extensive concern in energy storage devices such as supercapacitors due to its large interlayer spacing, high conductivity and good hydrophilicity. However, it is struggle to synthesize 1T-MoS₂ with stable 1T phase with high content. Herein, Ammonium ion intercalation molybdenum disulfide (A-MoS₂) with high 1T content and stable 3D microsphere structure was successfully synthesized using a facile hydrothermal method. We explained the feasibility of ammonium ion (NH₄⁺) intercalation through density functional theory (DFT) calculations and proved the successful intercalation of NH₄⁺ by XRD and XPS. Through XPS fitting, the 1T phase content is calculated as high as 83.1%. The as-prepared A-MoS₂ presents a stable 3D microsphere structure with the interlayer spacing expanded to 0.93 nm, which provides a wide ion diffusion channel that allows ions to pass through quickly. Moreover, the high 1T content increases the hydrophilicity of MoS₂, thereby improving the wettability of the electrode, which contributes to the interaction between the electrolyte and electrode. In 1 M Na₂SO₄, A-MoS₂ electrode material displays high specific capacitance of 228 F g^?1 at 5 mV s^?1 and retains 127 F g^?1 at 80 mV s^?1, which proves the good rate capability. Furthermore, the assembled α-MnO₂//A-MoS₂ asymmetric supercapacitor (ASC) displayed a wide operating voltage of 2.1 V. The assembled ASC displays a high energy density of 35.8 Wh?kg^?1 at a power density of 525.0 W kg^?1, which indicates excellent energy storage performance.     

基于气相色谱-离子迁移色谱分析不同贮藏方式对洋葱浆馕风味的影响

采用气相色谱-离子迁移谱（gas chromatography-ion mobility spectrometry，GC-IMS）对洋葱浆馕6 种不同贮藏条件下挥发性物质进行分析，包括低温贮藏、室温贮藏、真空贮藏、脱氧贮藏、保鲜剂贮藏和保鲜剂结合脱氧贮藏。研究表明：在洋葱浆馕中共鉴定出66 种挥发性风味物质，其中包括醇类9 种、酮类4 种、醛类18 种、酯类4 种、呋喃衍生物3 种，酸类1 种和未能识别的化合物27 种。随着贮藏时间的延长，低温贮藏和真空贮藏洋葱浆馕在贮藏期内醛类挥发性有机物基本不变，其他处理组的醛类挥发性有机物在贮藏期内变化呈降低的趋势。结合主成分分析和欧氏距离可以发现低温贮藏和其他贮藏方式的第0天挥发性物质种类和浓度较为接近，主成分分析图中点的位置也相聚在一起，说明低温贮藏馕的挥发性物质变化不明显。该研究建立不同贮藏方式洋葱浆馕挥发性气味指纹图谱，可视化出洋葱浆馕挥发性成分轮廓，为洋葱浆馕贮藏期间风味变化规律提供信息。     

Development of high pressure membraneless alkaline electrolyzer

A technology for cyclic generation of hydrogen and oxygen using electrodes made of variable valency material that does not need the use of separating ion-exchange membranes is presented. The technological solution enables to fabricate electrolyzers for uninterrupted producing high-pressure hydrogen with reduced energy intensity of the production. The total work for compressing 1 m³ of hydrogen and 0.5 m³ of oxygen has been estimated. Results of investigation of influence of discrete supply of DC current to the electrolysis cell, in order to improve the processes of gas evolution and to simplify the power systems of the electrolysis plant, have been considered. There is also considered an electrolysis installation equipped with a thermosorption compressor in which LaNi₅ is used as a hydride-forming compound. The comparative characteristics of the developed electrolyzer and the currently used hydrogen generators are given.     

LinkingPark: An automatic semantic table interpretation system

In this paper, we present LinkingPark, an automatic semantic annotation system for tabular data to knowledge graph matching. LinkingPark is designed as a modular framework which can handle Cell-Entity Annotation (CEA), Column-Type Annotation (CTA), and Columns-Property Annotation (CPA) altogether. It is built upon our previous SemTab 2020 system, which won the 2nd prize among 28 different teams after four rounds of evaluations. Moreover, the system is unsupervised, stand-alone, and flexible for multilingual support. Its backend offers an efficient RESTful API for programmatic access, as well as an Excel Add-in for ease of use. Users can interact with LinkingPark in near real-time, further demonstrating its efficiency.